pml-series ? p6lu-xxxxe/zh60enlf ? single and dual output ? sip7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/4 p6lu-xxxxe/zh60enlf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitor input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 3% short circuit protection indefinite (automatic recovery) line regulation 1.2% / 1% vin change load regulation (10% - 100%) 10% ripple and noise (20mhz bandwidth) 200 mv pk-pk temperature coefficient 0.03% / c general specifications efficiency see table i/o isolation voltage (3 sec. flash test) 6000 vdc i/o isolation capacity 10 pf, typ. i/o isolation resistance 1000 m ohm switching frequency 20 - 50 khz, typ. humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) >2.39 mhrs safety standard (designed to meet) iec 60950-1:2001 physical specifications clearance distance (input to output) 2.5 mm case material epoxy encapsulated (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 4.2g, typ. environment specifications operating temperature -40 to +85 c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection (10 mm distance required) rohs conform soldering 260c, max. (1.5 mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm l series p6lu - xxxxe/zh 60 en lf is a family of cost effective 1 w single & dual output dc-dc converters. these conver ters are in an ultra miniature sip7 case without compromising performanc e. the bigger case ensures the physical clearance of isolation barrier of 2.5mm which increases the reliability under high pot from 6kv d c. devices are encapsulated. high performance features: 6kv input/ output isolation, high efficiency, output voltage accuracy of 3%, input r ange of 10%, low output ripple and noise and long term short circuit protection. pml-series 1 watt unregulated single and dual output sip7 case 6 kv dc i/o isolation low coupling capacity rated voltage for 250 vrms rev.06-2009
pml-series ? p6lu-xxxxe/zh60enlf ? single and dual output ? sip7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/4 selection guide single output order # i n p u t v o l t a g e ( v d c ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 single output p6lu-053r3eh60enlf 5 3.3 303 69 - 75 220 p6lu-0505eh60enlf 5 5 200 70 - 77 220 p6lu-0509eh60enlf 5 9 111.1 70 - 80 220 p6lu-0512eh60enlf 5 12 83.3 70 - 80 220 p6lu-0515eh60enlf 5 15 66.7 70 - 80 220 p6lu-093r3eh60enlf 9 3.3 303 69 - 75 220 p6lu-0905eh60enlf 9 5 200 70 - 77 220 p6lu-0909eh60enlf 9 9 111.1 70 - 80 220 p6lu-0912eh60enlf 9 12 83.3 70 - 80 220 p6lu-0915eh60enlf 9 15 66.7 70 - 80 220 p6lu-123r3eh60enlf 12 3.3 303 69 - 75 220 p6lu-1205eh60enlf 12 5 200 70 - 77 220 p6lu-1209eh60enlf 12 9 111.1 70 - 80 220 P6LU-1212EH60ENLF 12 12 83.3 70 - 80 220 p6lu-1215eh60enlf 12 15 66.7 70 - 80 220 p6lu-153r3eh60enlf 15 3.3 303 69 - 75 220 p6lu-1505eh60enlf 15 5 200 70 - 77 220 p6lu-1509eh60enlf 15 9 111.1 70 - 80 220 p6lu-1512eh60enlf 15 12 83.3 70 - 80 220 p6lu-1515eh60enlf 15 15 66.7 70 - 80 220 p6lu-243r3eh60enlf 24 3.3 303 69 - 75 220 p6lu-2405eh60enlf 24 5 200 70 - 77 220 p6lu-2409eh60enlf 24 9 111.1 70 - 80 220 p6lu-2412eh60enlf 24 12 83.3 70 - 80 220 p6lu-2415eh60enlf 24 15 66.7 70 - 80 220 if you need other specifications, please enquire.
pml-series ? p6lu-xxxxe/zh60enlf ? single and dual output ? sip7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/4 selection guide dual output order # i n p u t v o l t a g e ( v d c ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 dual output p6lu-053r3zh60enlf 5 3.3 151.5 68 - 75 100 p6lu-0505zh60enlf 5 5 100 70 - 78 100 p6lu-0509zh60enlf 5 9 55.6 70 - 81 100 p6lu-0512zh60enlf 5 12 41.7 72 - 81 100 p6lu-0515zh60enlf 5 15 33.3 70 - 81 100 p6lu-093r3zh60enlf 9 3.3 151.5 68 - 75 100 p6lu-0905zh60enlf 9 5 100 70 - 78 100 p6lu-0909zh60enlf 9 9 55.6 70 - 81 100 p6lu-0912zh60enlf 9 12 41.7 72 - 81 100 p6lu-0915zh60enlf 9 15 33.3 70 - 81 100 p6lu-123r3zh60enlf 12 3.3 151.5 68 - 75 100 p6lu-1205zh60enlf 12 5 100 70 - 78 100 p6lu-1209zh60enlf 12 9 55.6 70 - 81 100 p6lu-1212zh60enlf 12 12 41.7 72 - 81 100 p6lu-1215zh60enlf 12 15 33.3 70 - 81 100 p6lu-153r3zh60enlf 15 3.3 151.5 68 - 75 100 p6lu-1505zh60enlf 15 5 100 70 - 78 100 p6lu-1509zh60enlf 15 9 55.6 70 - 81 100 p6lu-1512zh60enlf 15 12 41.7 72 - 81 100 p6lu-1515zh60enlf 15 15 33.3 70 - 81 100 p6lu-243r3zh60enlf 24 3.3 151.5 68 - 75 100 p6lu-2405zh60enlf 24 5 100 70 - 78 100 p6lu-2409zh60enlf 24 9 55.6 70 - 81 100 p6lu-2412zh60enlf 24 12 41.7 72 - 81 100 p6lu-2415zh60enlf 24 15 33.3 70 - 81 100 if you need other specifications, please enquire.
pml-series ? p6lu-xxxxe/zh60enlf ? single and dual output ? sip7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 4/4 package / pinning / derating modelcode datecode 1 2 5 6 7 9.80 (0.39) 19.50 (0.76) 15.24 (0.60) 2.54 (0.10) 0.50 (0.02) 0.50 (0.02) 2.13 (0.08) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. pe a k sip7 C ?enlf plastic case # single dual 1 +vin +vin 2 - vin - vin 5 - vout - vout 6 omitted common 7 +vout +vout pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load. - operation under no-load conditions will not damag e these devices, but they will not observe the list ed specifications. - for reduce converter?s ripple & noise, it is reco mmended to add a 4.7 f~100 f(4.7 f~68 f for dual output) capacitor at the output. for emi performance improvement, it is recommended to add a 12 h inductor and a 10 f~100 f capacitor at the input.
|
